The purpose of this degree project was to build laboratory equipment for a new course in Power electronics that starts this autumn 2010 at Uppsala University. The equipment is intended for student labs and it covers the most important areas of the course including rectifying, buck-/boost-converters and PWM-modulation. It is built as one sealed unit where all the electronics are built-in but visible and it has a connection board where students safely can connect the different circuits. The project has advanced from theoretical studies of circuit design, choosing of components and simulations to drawing the printed circuit board (PCB), soldering, case building, final testing and troubleshooting - basically most steps from an early idea to a final product. Measurements on the final product gave about the same results as the earlier simulations of the circuits and the result is overall satisfying..

Today electronics becomes more and more complex and to keep low costs and power consumption, both digital and analog parts are implemented on the same chip. The degree of automization for the digital parts have increased fast and is high, but for the analog parts this has not come through. This have created a big gap between the degrees of automization for the two parts and makes the analog parts the bottleneck in electronics develop. Research is ongoing at Electronics systems group at Linköping University target the increase of design automization for analog circuits. An optimizationbased approach for device sizing is developed and for this a good optimization method is needed which can find good solutions and meet the specification parameters.

The use of silicon carbide (SiC) as a base material in Power electronics has manyadvantages, including high breakdown voltage and excellent temperature endurance.However, the packaging of such electronics presents major challenges and there is aneed for packaging that can operate in higher temperature. The purpose of this thesishas been to develop a test method and verify the functionality of SiC powertransistors prototypes with a new packaging technique developed by Swerea IVF AB.It includes setting up an electrical test-bed for power and high temperature cyclingand analysis of the results. Even though test confirmed functionality after thepackaging process, (at room temperature) the performance seemed to have been reduced. This could be a result of the measurement setup and the packaging process.In higher temperature the transistors failed to operate longer than a couple ofminutes which showed the weaknesses in the design and the challenges with this typeof packaging..

In the electronic industrials, power control of AC motors is commonly used. For example power control of a washing machine motor, a vacuum cleaner motor or a coffee machine motor. The company Rejlers Ingenjörer AB has many projects where power control of AC motors is included. A prototype card for this task can save time and money for the company in the future and this is the reason for this thesis.The motors are power controlled by a TRIAC and control of the trigging pulses to the TRIAC. This card is modularly built and can easily be adapted for future projects where the power control of AC motors are included.The prototype card can be used as a subsystem in a larger electronics projects or as it is in lab environment for testing and evaluating new motors..

With background in the rapidly growing need to find solutions for sustainable energy production and the increasing interest for wind power, this report was written. With take-off point from the wind power plant Big Glenn, which has been built in the harbour of Gothenburg, a model of the adjacent power grid has been created in Simulink/SimPowerSystems. Parameters for the power grid and its components has been provided by Göteborg Energi Nät, that has also been the supplier of measurement data of produced power, the power need from loads in the vicinity, voltage levels, current values and also the variation of power factor at the wind power plant.The SimPowerSystems model has been used to perform simulations of power flow in the grid. These simulated values have then been compared to the measured values to verify the functionality of the model. Further, the model has been used to perform simulations of a grid fault, which causes a voltage drop.

This thesis is the result of the author?s interest in music and electronics, namely the design and manufacturing of a stereo sound system with an active crossover. In short it can be stated that an active crossover has many advantages over its traditional passive counterpart. The active design naturally results in a more complex system comprised of a multiple number of components. This report deals with the theoretical aspects of preamplifiers, crossovers and power amplifiers as well as power supply and control.

With background in the rapidly growing need to find solutions for sustainable energy production and the increasing interest for wind power, this report was written. With take-off point from the wind power plant Big Glenn, which has been built in the harbour of Gothenburg, a model of the adjacent power grid has been created in Simulink/SimPowerSystems. Parameters for the power grid and its components has been provided by Göteborg Energi Nät, that has also been the supplier of measurement data of produced power, the power need from loads in the vicinity, voltage levels, current values and also the variation of power factor at the wind power plant.The SimPowerSystems model has been used to perform simulations of power flow in the grid. These simulated values have then been compared to the measured values to verify the functionality of the model. Further, the model has been used to perform simulations of a grid fault, which causes a voltage drop.

Leisure boats of today have a lot of electronics that needs battery power to work. In additionto that electric propulsion systems have gotten more popular lately, which further increasesthe demand for high battery capacity. The batteries used are mostly lead-acid batteries and toget the most out of the batteries it is important to treat them right. To optimize the electricsystem it is important to have knowledge of how the batteries and the electric motor are usedand which factors affect e.g. efficiency and recharging.A new electric drive that can replace old diesel engines is being developed and needs testingand evaluation.

This master thesis describes the development of an UPS module. UPS is an acronym for Uninterruptable Power Supply. The UPS module has been developed at the company AerotechTelub AB. The UPS module delivers the necessary voltage and current in case of a power interrupt. If a power interrupt occur, the computer system has one to three minutes available to store data and shut down correctly.

In this thesis a number of energy saving methods for a multiplier on algorithmic level are investigated. For the investigation a multiplier is constructed in VHDL, after which the circuit's performance is investigated. A number of techniques for reduced power consumption are introduced in the circuit and are then evaluated. The conclusions are that all investigated methods, pipelining, interleaving and voltage scaling, should be maximally made use of in order to minimize the power consumption..

The goal of this thesis work is to enable an existing UHF radar to operate in the VHF band instead. In order to achieve this, new coherent local oscillators are required. Different options are suggested and one of them is implemented and analyzed..

There is always a need for more effective ways to store energy in order to reduce the human impact on the environment. One step on the way can be the use of flywheels as kinetic energy storage devices. Low frictional losses are essential for a flywheel to be effective. To minimize these losses active magnetic bearings (AMB) can be used to keep the shaft centered instead of the more conventional ball-bearings. AMBs use actuators and a fast control system that needs correct and noise-free measurement data of the shaft position and the current in the actuators to work properly.This thesis explains the process of constructing Power electronics and a current measurement system for active magnetic bearings (AMB).

The goal of this project was to implement and compare Invere Discrete Cosine Transform using three methods i.e. by bit parallel, digit serial and bit serial. This application describes a one dimensional Discrete Cosine Transform by bit prallel method and has been implemented by 0.35 ìm technology. When implementing a design, there are several considerations like word length etc. were taken into account.

A new FPGA suitable for space applications has just reached the market. To investigate whether there are any possible flaws or limitations similar to those previously seen on FPGAs, an evaluation has to be done. This master thesis contains the evaluation of this new radhard FPGA with focus on possible design limitations and package related electrical phenomena.Areas evaluated: Ground-/VDD bounce, Cross talk, Rise time sensitivit, Power cycling, Power consumption, Place and route tool, Radiation hardnessThis report contains all steps in the evaluation. From method to measurements, comparisons, theory, results and conclusions. In the evaluation work, special effort has been made to develop designs that really stress the FPGA to find potential problems.

Implementering av FIR filter kan göras på olika sätt. I detta examensarbete har två olika varianter beskrivits med hjälp av VHDL, syntetiserats, simulerats och sedan jämförts med avseende på effektförbrukning..